P1800 Saint: The Ultimate Volvo Restomod

May 27, 2023

"It's hard to take something so good and make it even better."

These are the words of Swedish car builder Torbjörn von Braun as he described the main challenge of his latest creation – a Volvo P1800 restomod nicknamed the Saint – ahead of its unveiling at this year's Elmia Custom Motor Show. As it turns out though, this was a challenge not only accepted, but totally overcome.

The original P1800 was manufactured by Volvo between 1961 and 1973, and this project has some real credibility thanks to the people involved. A collaboration between von Braun Sports Cars and Zachau Design, the P1800 Saint team consists of ex-Volvo design employees from back in the car's era. That includes Pelle Petterson, the P1800's original designer.

Like many restomods, the P1800 Saint retains the silhouette of the original car, but even before you delve beneath the skin it's a very different machine to the P1800s that left the Volvo factory more than 50 years ago.

Buyers can either supply their own P1800 base for the Saint conversion or have von Braun Sports Cars source a suitable candidate for them. Each car is stripped right down to its bare shell before being acid dipped and then improved in a number of ways. Any rusted panels are replaced, the transmission tunnel is reinforced, an epoxy primer and sealer is applied to all joints for rust protection, and a sound-absorbing rubber coating is added to the underside.

When it comes to the exterior, von Braun Sports Cars is offering the P1800 Saint with two body panel options: steel or ultra-light carbon fiber. After final paint, further carbon pieces are added to both versions.

The exterior has a few tasteful upgrades for the modern era – including the option of a speed-sensitive active rear wing/air brake – but one really stood out to me. These 17-inch custom forged wheels – named the Lucky 7 – were designed by Hans Phillip Zachau (of Zachau Design), taking inspiration from racing machines of the 1960s and ’70s.

Behind the wheels you can catch a glimpse of the brake upgrade, which features Brembo 4-piston callipers and 330mm carbon-ceramic brake discs in the front, and a Brembo 4-piston/320mm setup out back with an additional calliper for the park brake. Furthermore, ABS is added, but this can be disabled when ‘Chase Mode’ is enabled. I like the sound of that!

The suspension is completely bespoke, built around double wishbones front and rear. It's also a visual aspect of the P1800 Saint, with the pushrod rear suspension featuring fully adjustable Öhlins coilovers on show, but sealed off from the cabin with a glass screen.

That cabin is something very special too.

Everything in here has been custom-designed and finished, but is largely based on the original fit-out. The door panels, roof liner and front seats are upholstered in red leather.

The original dash layout has been preserved, but it's re-trimmed and uses gauges made by watchmakers. The two-spoke steering wheel is an iconic feature of the original P1800, and the design has been retained in the Saint, albeit in a smaller size and with a more modern look.

As you’d expect, everything is custom-tailored so trim options are endless. A rear seat section – constructed from carbon fiber of course – was on display next to the Saint demo car, showcasing a different look.

Earlier, I mentioned two choices for the body panels; when it comes to the P1800 Saint's engine, you’ve got three. The first is a nostalgic, naturally-aspirated four-cylinder Volvo engine, fed by a carburettor and outputting 150hp+. The second is a naturally-aspirated 2.4L Volvo five-cylinder with fuel injection, good for 250hp+. The final engine, as seen in the demo car, is a turbocharged 2.4L five-cylinder Volvo T5. This one is making around 450hp – which is plenty for a car that weighs just under 1,100kg or 2,425lb – but 750hp is possible.

Mounted longitudinally, the engine marries up to either a manual transmission, or with the two 2.4L engines, the option of a 7-speed Getrag dual-clutch transmission and Sellholm Tuning differential to drive the rear wheels. The DCT configuration provides a comfortable ride with all the power and drivability of a GT-spec car, which is exactly what this is.

There's so much to this restomod that my quick spotlight has definitely not done the P1800 Saint justice. If I have the chance for a closer look in the future, you can count on a full feature.

Alen HasetaInstagram: hazetaa

Volvo related stories on Speedhunters

E-mail is already registered on the site. Please use the Login form or enter another.

You entered an incorrect username or password

Those wheels and seats look shocking. I like the engine ideas though.

Not everyone's cup of tea I suppose.

Absolutely yes. On point, and looks to be a great contender for more restomods. Nice to see Volvos getting more love. Great share!

NO.2 is already in the works!

wheels remind me of Bentley for some reason. It is different.

I can totally see the resemblance.

As if it couldn't get any better this restomod looks so damn good and is definitely one of the best out there

I don't think the pictures give it justice to be fair. This one has to be seen in RL.

9000 rpm redline? How is it possible? Volvo stock engines aren't known to be high revving. They aren't Honda's VTEC or Porsche's NA engines (the one in GT3). Perhaps the tachometer / rev counter is there for show purpose only. The car looks very clean/

What a great resto mod. I think I read about it in the Grassroots Motosports mag a year ago. I'll bet that thing is a corner carver with that custom suspension.

Magnificent. It pays homage to the original but incorporates so much more with The tastefully updated/upgraded mechanical features. I hope we get to see it in the UK sometime.

Every time somebody wrongly puts a P in front of the 1800 a puppy cries. Only cars in 61-62, built by Jensen, are P1800s. After that they become the carbureted 1800S, fuel injected 1800E, and the 3 door 1800ES.